Measuring stepped wear at the sides of the housing

Measuring stepped wear across the middle of the housing

Measuring stepped wear caused by the oil seal

Use a dial indicator with a sled attachment (gauge body) to check for wear on the rotor contact surfaces of the housing. Mazda offers such an attachment under part number 49-0727-570 or equivalent. To check for stepped wear on the rotor housing sliding surfaces, mount the dial indicator on the sliding surface of the housing. To measure stepped wear caused by the side seal at the sides of the housing, move the dial indicator gauge feeler to and fro as shown in the illustration. The wear limit is 0.0039 in. (0.10mm). Check the side seal stepped wear across the middle of the housing with the dial indicator, moving it as shown in the illustration. The wear limit inside the oil seal tracing marks is 0.0004 in. (0.01mm), and the wear limit outside the oil seal tracing marks is 0.0039 in. (0.10mm). Check for stepped wear by the oil seal with the dial gauge. The wear limit is 0.0008 in. (0.02mm).

If the front, intermediate and/or rear side housings are beyond the above wear limits, they can be ground if the required finish can be maintained. If the wear is greater than the values provided above, replace the housing.

The wear at either end of the minor axis is greater than at any other point on the housing. However, this is normal and should not be cause for concern.

Front Stationary Gear and Main Bearing

Examine the teeth of the stationary gear for wear or damage.

Be sure that the main bearing shows no signs of excessive wear, scoring, or flaking.

Check the main bearing-to-eccentric journal clearance by measuring the journal with a vernier caliper and the bearing with a pair of inside calipers. The standard clearance is 0.0016-0.0031 in. (0.04-0.08mm). If the clearance exceeds the limit, replace the front main bearing as described later in this section.

Front Main Bearing Replacement

Unfasten the securing bolts, if used. Remove the stationary gear and main bearing assembly from the housing, using puller tool 49-0813-235 or equivalent.

Press the main bearing out of the stationary gear.

Press a new main bearing into the stationary gear, so that it is in the same position as the old one.

Align the slot in the stationary gear flange with the dowel pin in the housing, then press the gear into place. On later engines, align the bearing lug with the slot in the gear. Install the securing bolts, if applicable.

Rear Stationary Gear and Main Bearing

Inspect the rear stationary gear and main bearing in a similar manner to the front. In addition, examine the O-ring, which is located in the stationary gear, for signs of wear or damage. Replace the O-ring, if necessary. If the stationary gear must be replaced, follow the rear main bearing replacement procedure.

Rear Main Bearing Replacement

Remove the rear stationary gear securing bolts.

Drive the stationary gear out of the rear housing with a brass drift.

Apply a light coating of grease to a new O-ring and fit it into the groove on the stationary gear.

Apply sealer to the flange of the stationary gear.

Install the stationary gear on the housing so that the slot on its flange aligns with the pin on the rear housing. On later engines, align the bearing lug with the housing slot. Use care not to damage the O-ring during installation.

Tighten the stationary gear bolts evenly, in several stages, to 12-17 ft. lbs. (16-23 Nm).

Rotor Housings

Examine the inner margin of both housings for signs of gas or water leakage.

Wipe the inner surface of each housing with a clean cloth to remove the carbon deposits.

Clean all of the rust deposits out of the cooling passages of each rotor housing.

Checking rotor housing width

Remove the old sealer using the proper removal solvent.

Examine the chromium-plated inner surfaces for scoring, flaking, or other signs of damage. If any are present, the housing must be replaced.

Check the rotor housings for distortion by placing a straightedge on the axes.

If distortion exceeds 0.002 in. (0.05mm), replace the rotor housing.

Check the widths of both rotor housings, at points A, B, C, and D near the trochoid surfaces of each housing, using a vernier caliper, as illustrated. Compare the difference between the value obtained at point A and the minimum value of points B, C and D. If the difference between the values obtained is greater than 0.0024 in. (0.06mm), replace the housing. A rotor housing in this condition will be prone to gas and coolant leakage.

Rotors

Check the rotor for signs of blow-by around the side and corner seal areas.

The color of the carbon deposits on the rotor should be brown, just as in a piston engine. Usually, the carbon deposits on the leading side of the rotor are brown, while those on the trailing side tend toward black (as viewed from the direction of rotation).

Remove the carbon on the rotor with a scraper or extra fine emery paper. Use the scraper carefully when cleaning the seal grooves to avoid any damage.

Wash the rotor in solvent and blow it dry with compressed air.

Examine the internal gear for cracks or damaged teeth. If the internal gear is damaged, the rotor and gear must be replaced as a single assembly.

With the oil seal removed, check the land protrusions by placing a straightedge over the lands. Measure the gap between the rotor surface and the straightedge with a feeler gauge.

Check the clearance between the housings and the rotor on both of its sides:

Measure the rotor width with a vernier caliper at the points indicated in the corresponding illustration.

Compare the rotor width against the width of the previously measured rotor housing.

Replace the rotor, if the difference between the two measurements is not 0.0047-0.0074 in. (0.12-0.19mm) for the 1979-85 carbureted engine or 0.0047-0.0083 in. (0.12-0.21mm) for the 1984-90 fuel injected engine.

If the clearance exceedsthe specified values, replace the rotor. If the clearance is lessthan specification, it means that the internal gear must be removed. To dislodge the gear from the rotor bore, smack it lightly with a plastic-faced hammer, being careful not to damage the rotor. With the gear removed, recheck the side housing-to-rotor clearance again.

The corner seal bores can be checked with a gauge (tool number 49 0839 15 or equivalent), available from Mazda. If neither end of the gauge can be fit into the bores, it is safe to reuse the original corner seals. If the "go" side of the gauge does fit into the bore, but the larger "no go" side does not, use new seals. If both sides of the gauge fit into the bores, the rotor must be replaced.

Check the rotor bearing for wear, flaking, scoring or damage. Replace the bearing if these conditions are found. Check the bearing oil clearance by measuring the appropriate bearing journal diameter on the eccentric shaft with a micrometer. Next, measure the inner diameter of the rotor bearing.

The standard rotor bearing journal diameter is 2.913 in. (74mm).

Find the oil clearance by subtracting the rotor bearing diameter from the rotor journal diameter. The standard clearance is 0.0016-0.0031 in. (0.04-0.08mm). If the clearance is greater than 0.0039 in. (0.10mm), replace the rotor bearing as described later in this section.

Rotor Bearing Replacement

Check the clearance between the rotor bearing and the rotor journal on the eccentric shaft. Measure the inner diameter of the rotor bearing and the outer diameter of the journal. The wear limit is 0.0039 in. (0.1mm); replace the bearing if it exceeds specification.

Place the rotor on the support so that the internal gear is facing downward. Using puller tool 49-0813-240 (or equivalent) without its adaptor ring, press the bearing out of the rotor. Being careful not to damage the internal gear.

Place the rotor on the support with the internal gear facing upward. Place the new rotor bearing on the rotor so that the bearing lug is in line with the slot of the rotor bore.

Remove the screws which attach the adaptor ring to the special tool. Using the special tool and adaptor ring, press fit the new bearing until the bearing is flush with the rotor boss.

Oil Seal Inspection

Examine the oil seal while it is mounted in the rotor.

If the width of the oil seal lip is greater than 0.020 in. (0.5mm), replace the oil seal.

If the protrusion of the oil seal is greater than 0.020 in. (0.5mm), replace the seal.

Oil Seal Replacement

Pry the seal out by inserting a small prybar into the slots on the rotor. Be careful not to deform the lip of the oil seal if it is to be reinstalled.

Fit both the oil seal springs into their respective grooves, so that their ends are facing upward and their gaps are opposite each other on the rotor.

Insert a new O-ring into each of the oil seals. Before installing the O-rings into the oil seals, fit each of the seals into its proper groove on the rotor. Check to see that all of the seals move smoothly and freely.

Coat the oil seal groove and the oil seal with clean engine oil.

Gently press the oil seal into the groove with your fingers. Be careful not to distort the seal. Be sure that the white mark is on the bottom side of each seal when it is installed.

Repeat the installation procedure for the oil seals on both sides of each rotor.

Apex Seals

Remove the carbon deposits from the apex seals and their springs. Do not use emery cloth on the seals, as it will damage their finish.

Wash the seals and the springs in cleaning solution.

Check the apex seals for cracks.

Test the seal springs for weakness.

Use a micrometer to check the seal height.

With a feeler gauge, check the side clearance between the apex seal and the groove in the rotor. Insert the gauge until its tip contacts the bottom of the groove. If the gap is greater than 0.0035 in. (0.09mm) for the 1983-85 12A engine, or 0.0059 in. (0.15mm) for the 1984-90 13B engine, replace the seal. The standard range for non-turbo engines is 0.0024-0.0040 in. (0.06-0.10mm) and 0.0020-0.0040 in. (0.05-0.10mm) for turbo engines.

Check the gap between the apex seals and the side housing by using a vernier caliper to measure the length of each apex seal. Compare this measurement to the minimum figure obtained for the rotor housing width.

Check the apex seal spring for wear and measure its free height. If less than 0.2165 in. (5.5mm), replace the spring.

If the seal is too long, sand the ends of the seal with emery cloth until the proper length is reached. Do not use the emery cloth on the faces of the seal.

Side Seals

Check the side seal free movement in the rotor groove. You should be able to press down along its length with your finger.

Measure the side seal protrusion from the rotor surface. If the protrusion is less than 0.02 in (0.5mm), replace the side seal spring.

Measure the clearance between the side seal and its groove in the rotor with a feeler gauge. (The standard clearance is given in the specification chart, earlier in this section.) If the clearance is greater than 0.0039 in. (0.10mm), replace the side seal.

Using a feeler gauge, check the clearance between the side seal and the corner seal when the seals are installed on the rotor. If the clearance is greater than 0.0157 in. (0.4mm), replace the side seal. When installing a new side seal, correct the clearance between the side and corner seals by grinding the end of the side seal and the rounded corner seal with a fine file. The clearance should be 0.0020-0.0059 in. (0.05-0.15mm). If it exceeds this, the performance of the seals will deteriorate.

There are 4 different types of side seals, depending upon location. Do not mix up the seals and be sure to use the proper type of seal for replacement.

Corner Seals

Inspect the corner seal and spring for wear, cracks, or damage and replace, if necessary.

Make sure the corner seal has free movement by pressing on it with your finger.

Measure the corner seal protrusion from the rotor surface. It should protrude at least 0.02 in (0.5mm). If not, replace the corner seal spring.

Inspect the corner seal spring for wear.

Seal Springs

Check the seal springs for damage or weakness. Be especially careful when checking the spring areas which contact either the rotor or the seal.

Eccentric Shaft

Wash the eccentric shaft in solvent and blow the oil passages dry with compressed air.

Check the shaft for wear, cracks, or other signs of damage. Make sure that none of the oil passages are clogged.

Exploded view of eccentric shaft. Remove the oil jet plug (indicated by the arrow) to check the spring and steel ball

Measure the shaft journals. Replace the shaft if any of its journals show excessive wear.

Check eccentric shaft run-out. Rotate the shaft slowly and note the dial indicator reading. Run-out should not exceed 0.0047 in. (0.12mm) as measured from the end of the shaft. If run-out is greater than specification, replace the eccentric shaft.

Check the blind plug at the end of the shaft. If it is loose or leaking, remove it with an Allen wrench and replace the O-ring.

Check the operation of the needle roller bearing for smoothness by inserting a mainshaft into the bearing and rotating it. Examine the bearing for signs of wear or damage. Check the oil jet for spring weakness, sticking or ball damage.

Replace the bearings, if necessary, with special bearing replacer tools 49-0823-073 and 49-0823-072, or equivalent.

Needle Bearing and Thrust Plate

Inspect the needle bearing for wear and damage.

Inspect the bearing housing and the thrust plate for wear and damage.

Oil Pump Drive Chain and Sprocket

Lay the chain on a flat surface and check the entire length for broken links.

Check the oil pump drive and driven sprockets for missing and broken teeth.

Replace parts as necessary.

Assembly of Internal Components

Replace all O-rings, rubber seals and gaskets with new parts. Place the rotor on a rubber pad or cloth. Coat all the engine sliding surfaces with clean engine oil.

Install the oil seal rings in their respective grooves in the rotors with the edge of the spring in the stopper hole. The oil seal springs are painted cream or blue in color. The cream colored springs must be installed on the front faces of both rotors. The blue colored springs must be installed on the rear faces of both rotors. When installing each oil seal spring, the painted, square side of the spring must face upward toward the oil seal.

Oil seal spring installation

Coat the new O-ring with clean engine oil and install in each seal groove. Place each oil seal in the groove so that the square edge of the spring fits in the stopper hole of the oil seal. Push on the head of the oil seal slowly with your fingers, being careful that the seal is not deformed. Be sure that the oil seal moves smoothly in the groove beforeinstalling the O-ring. An old seal can be used as an installation tool.

Lubricate each oil seal and groove with engine oil. Check the movement of the seal. It should move freely when the head of the seal is pressed.

Check the oil seal protrusion and install the seals on the other side of each rotor. Oil seal protrusion must not exceed 0.016 in. (0.4mm).

Install the apex seals (without springs and side pieces) into their respective grooves, so that each side piece will be positioned to the rear side of the rotor.

Install the corner seal springs and corner seals into their respective grooves.

Install the side seal springs and side seals into their respective grooves.

Confirm the smooth movement of each seal by pressing its head.

When meshing the internal and stationary gears, make sure at least one of the rotor apexes is positioned as shown